PG 40598 PU PE BLACK 40025 FL RED PE #2

JA6A/LP/BLACK PE-25CF/000 BLACK PURPLE PE CD4484

BLACK 392667 YELLOW PE WARM GRAY 5C PE OUT

PINE NEEDLE PE FR WHITE PE MB2580G BLACK

EGER YELLOW PE UV ORANGE PE 2 DX9 BLACK PP20TF

PG05/BLACK STRAW PE TONER V1 BLACK PE TONER V1

PE DARK BLUE V2 GREEN - PE VERSION TPE BLACK CMPD

PE BLACK F40 PE BLACK F80 (30%) BLACK

Deep Black for Polyester Textiles Renol™ Fiber Colorants Deep Black Colorants for PET Fibers OnColor™ NIR Sortable Black Colorants

Vents should be placed at the intersection of each 90° bend in the runner system off of the cold slug well and vented to atmosphere PROBLEM CAUSE SOLUTION Black Specks Contamination • Purge barrel with general purpose PP • Verify correct nozzle is being used • Pull screw for cleaning Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Decrease injection speed • Use appropriately sized barrel Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Decrease injection speed • Use appropriately sized barrel Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded-in stress Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Fibers/Minerals on Surface or Uneven Surface Appearance Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed Insufficient packing • Increase hold pressure and time • Increase shot size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Loose clamp • Reset mold height • Increase clamp tonnage Troubleshooting Recommendations PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Adjust transfer position to 98% full • Increase shot size Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression Shrink Too much shrink • Increase cooling time • Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness Melt too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Troubleshooting Recommendations (continued) PROBLEM CAUSE SOLUTION Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Warp Process related • Increase cooling time • Increase melt temperature • Increase pack pressure • Increase pack time • Decrease mold temperature Mold design • Inspect for non-uniform mold cooling Part design • Inspect for non-uniform wall thickness Temperature control unit incorrect temperature • Check settings • Inspect thermocouple Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase injection rate • Increase mold temperature Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.