Safety Data Sheets Technical Data Sheets Browse our library of product data sheets containing technical descriptions and details.

Surface energy match between the thermoplastic elastomers and the rigid thermoplastic substrate. 2. Molecular interaction between the thermoplastic elastomer and the rigid thermoplastic. Matching the surface energy of the known thermoplastic elastomers chemistries with various rigid thermoplastics is illustrated in Figure 1.

Technical Data Sheets Safety Data Sheets Safety Data Sheets

Technical Data Sheets Safety Data Sheets Safety Data Sheets

Why Choose Thermoplastic Composite Panels? FR COMPOSITE PANELS Our Hammerhead FR composite panels consist of specially formulated continuous fiber reinforced thermoplastic (CFRTP) sheets bonded to a thermoplastic foam core. Interested in testing thermoplastic composites for your next project?

Technical Data Sheets Complēt™ Moisture Resistant Long Fiber Thermoplastic Nylons Replacing Aluminum with Long Fiber Thermoplastics (LFT)

ARTISAN™ PRE-COLORED THERMOPLASTICS NYLON (PA6) FORMULATIONS PROCESSING GUIDE 2 Artisan Pre-Colored Thermoplastics Artisan™ Pre-Colored Thermoplastics Artisan™ thermoplastics are vibrant, pre-colored high-gloss, scratch resistant engineered polymers formulated to replace paint for superior results. Cut vent depths to 0.0007″–0.0015″ Draft Angle Maintain a minimum draft angle of 1° per side 4 Artisan Pre-Colored Thermoplastics Troubleshooting Recommendations Problem Cause Solution Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Check thermocouples and heater bands Shot size • Increase shot size • Adjust transfer position to 98% full • Increase cushion Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel • Decrease injection speed Gate location and/or size • Relocate gate to non-stress area • Increase gate size to allow higher flow rate and lower molded-in stress Wet material • Check moisture. Sink Marks Melt too hot • Decrease nozzle and barrel temperatures• Decrease mold temperature Insufficient material volume • Adjust transfer position • Increase shot size • Increase injection rate • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness Processing Guide 5 Troubleshooting Recommendations Problem Cause Solution Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height• Increase clamp tonnage Shrink Too much shrink • Increase cooling time• Decrease mold temperature Too little shrink • Decrease cooling time • Increase mold temperature Burning Process related • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate • Reduce decompression Mold design • Clean, widen and increase number of vents• Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase injection rate • Increase pack and hold pressure • Increase melt temperature • Increase mold temperature Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location 6 Artisan Pre-Colored Thermoplastics Problem Cause Solution Warp Process related • Increase melt temp • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Adjust transfer position • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination Process related • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting Troubleshooting Recommendations Processing Guide 7 Troubleshooting Recommendations Problem Cause Solution Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

Thermoplastic Polymer Matrix A thermoplastic is not cross-linked, so it can be re-melted and re-formed, much like an ice cube that can melt and re-freeze. Advantages of Thermoplastics

NEUSoft™ Thermoplastic Polyurethanes Versaflex™ HC Thermoplastic Elastomers OnFlex™ Thermoplastic Elastomers

PVC EDGE BANDING MANUFACTURER E X T R U S I O N S H E E T & S T R A P • Meet the diverse coefficient of friction (CoF) requirements across various film structures and compositions for a wide range of applications • Improve the speed of slip blooming and ensure consistent slip performance post-film production • Preserve excellent optical and mechanical properties • Compliance with food regulations for end packaging in food sealant applications • Achieved the optimal flowability of liquid white and liquid orange, ensuring consistent color through suitable mixing with other colorants • Ensured lot-to-lot consistency with DE value of less than 0.5 • Supported customers in achieving stable and high-quality coloration during their PVC processing ColorMatrix Liquid Color Concentrates KEY REQUIREMENT WHY AVIENT AVIENT SOLUTION FUNCTIONALITY + COMPLIANCE Avient Corporation 1 • Meet the diverse coefficient of friction (CoF) requirements across various film structures and compositions for a wide range of applications • Improve the speed of slip blooming and ensure consistent slip performance post-film production • Preserve excellent optical and mechanical properties • Compliance with food regulations for end packaging in food sealant applications KEY REQUIREMENT • Standard colorant for internal color matching in PVC sheet applications • Manufactured with phthalate-free plasticizer • Good thermal stability and compatibility with PVC resin for a wide rang of color index choices • Compliance with heavy metal-free and RoHS regulations LIQUID COLOR CONCENTRATES AND DOSING | AVIENTLEARN MORE KEY REQUIREMENTS Copyright © 2025, Avient Corporation.