Suitable for PET and rPET preforms and bottles, it can be added to preforms providing the following benefits: • Improved blowing performance • Potential for increased rPET content • Increased mechanical strength • Potential for lightweighting • Improved performance through the recycle process • Reduced energy consumption • No pre-drying requirements SmartHeat RHC can contribute towards improved productivity, reduced manufacturing costs, improved sustainability, and can broaden the scope for bottle design.

These activities have a cumulative effect on reducing our operational energy needs and thus our impacts on the environment. We localize R&D solutions to enable environmental benefits, such as reduced energy use, decreased water use, and fuel savings. 案例分析：Avient completed 74 energy saving activities in 2020 that cumulatively reduce yearly emissions by 6,800 MT CO2e, hence reducing the company exposure to commodity fluctuations and regulatory changes.

Step each 90° bend in the system down in size (from sprue to gate) approximately 1/16" (1.5mm) to reduce pressure drop PROBLEM CAUSE SOLUTION Incomplete Fill Melt and/or mold temperature too cold Mold design Shot Size • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection speed • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line • Increase shot size • Increase cushion Brittleness Melt temperature too low Degraded/Overheated material Gate location and/or size • Increase melt temperature • Increase injection speed • Measure melt temperature with pyrometer • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Relocate gate to nonstress area • Increase gate size to allow higher flow speed and lower molded-in stress Fibers on Surface (Splay) Melt temperature too low Insufficient packing • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Sink Marks Part geometry too thick Melt temperature too hot Insufficient material volume • Reduce wall thickness • Reduce rib thickness • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase shot size • Increase injection rate • Increase packing pressure • Increase gate size Flash Injection pressure too high Excess material volume Melt and/or mold temperature too hot • Decrease injection pressure • Increase clamp pressure • Decrease injection speed • Increase transfer position • Decrease pack pressure • Decrease shot size • Decrease injection speed • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed TROUBLESHOOTING RECOMMENDATIONS PROBLEM CAUSE SOLUTION Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Burning Melt and/or mold temperature too hot Mold design Moisture • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection speed • Clean, widen and increase number of vents • Increase gate size or number of gates • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures too low Mold design • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection speed • Increase mold temperature • Decrease injection speed • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation Mold design • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection speed • Increase number of gates Sticking in Mold Cavities are overpacked Mold design Part is too hot • Decrease injection speed and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time • Increase draft angle • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time TROUBLESHOOTING RECOMMENDATIONS www.avient.com Copyright © 2020, Avient Corporation.

Step each 90° bend in the system down in size (from sprue to gate) approximately 1.5mm (1/16") to reduce pressure drop. 5. Maintain a minimum draft angle of 1° per side. 4 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase mold temperature • Increase injection rate • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase shot size • Increase cushion • Decrease transfer position Brittleness Low melt temperature • Increase melt temperature • Increase injection rate • Measure melt temperature with pyrometer Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Decrease screw rpm Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers on Surface (Splay) Melt temperature too low • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm Insufficient packing • Increase pack and hold pressure, and time • Increase shot size • Increase gate size Processing Guide 5 Problem Cause Solution Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness • Maintain nominal wall thickness Melt too hot • Decrease nozzle and barrel temperatures• Decrease mold temperature Insufficient material volume • Increase shot size • Increase injection rate • Increase pack pressure/time • Increase gate size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Decrease injection rate • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size • Decrease injection rate Melt and/or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease screw speed Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease mold temperature • Decrease injection speed • Decrease screw rpm • Increase venting • Increase cooling time Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase melt temperature • Increase mold temperature • Increase injection speed • Increase screw rpm • Decrease cooling time Troubleshooting Recommendations 6 Therma-Tech Troubleshooting Recommendations Problem Cause Solution Burning Melt and/or mold too cold • Decrease nozzle and barrel temperatures • Decrease mold temperature • Decrease injection rate Mold design • Clean, widen and increase number of vents• Increase gate size or number of gates Moisture • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase melt temperature • Increase vent width and locations • Increase injection rate • Increase mold temperature Mold design • Decrease injection rate • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Increase cooling time • Increase melt temperature • Decrease injection pressure and injection rate Mold design • Increase number of gates Sticking in Mold Cavities are overpacked • Decrease injection rate and pressure • Decrease pack and hold pressure • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle Part is too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature • Increase cooling time 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

These properties, coupled with a wide array of base engineering thermoplastics, deliver the distinct benefits of LubriOne: • Reduced friction and heat buildup between interacting surfaces • Reduced noise and vibration among components in relative motion • Reduced weight and improved design freedom • Lower long–term maintenance costs when grease and other lubricants are eliminated Copyright © 2023, Avient Corporation.

Reducing Carbon Footprint What is carbon footprint? How does Avient help reduce carbon footprint? Our efforts are aimed at reducing the quantity of hazardous and non-hazardous waste generated.

 Addressable market exceeds $40 billion  Strong performance demonstrates that our strategy and execution are working  Megatrends and emerging opportunities align with our strengths  Innovation and services provide differentiation, incremental pricing power, and competitive advantage  Strong and proven management team driving growth and performance PolyOne Corporation Page 18 Appendix PolyOne Corporation Page 19 $0.17 $0.22 $0.24 $0.31 $0.44 $0.46 $0.00 $0.25 $0.50 Q1'10 Q1'11 Q1'12 Q1'13 Q1'14 Q1'15 Adjusted EPS $30 $34 $25 $30 $35 Q1 2014 Q1 2015 GCAI Operating Income (in millions) $18 $23 $15 $20 $25 Q1 2014 Q1 2015 GSEM Operating Income (in millions) Q1 2015 Financial Highlights  Global Specialty Engineered Materials’ operating margin of 16.3% above the 2015 target  Global Color Additives and Inks’ operating margin grew to 16.2%  First quarter adjusted EPS has grown on average 23% per year since 2010 +26% +11% PolyOne Corporation Page 20 Appliances 2% Building & Construction 12% Consumer 7% Electrical & Electronics 1% Healthcare 6% Industrial 14% Packaging 31% Textiles 7% Transportation 8% Wire & Cable 12% 1.7% 4.6% 5.1% 5.5% 7.2% 8.1% 9.7% 12.2% 16.2% 20%+ 2006 2007 2008 2009 2010 2011 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales At a Glance Global Color, Additives and Inks 2014 Revenues: $0.9 Billion Solutions Expanding Profits 2014 Revenue by Industry Segment 14.7% Platinum Vision United States 44% Europe 36% Canada 2% Asia 12% Latin America 6% PolyOne Corporation Page 21 Appliances 4% Building & Construction 3% Consumer 18% Electrical & Electronics 16% Healthcare 12% Industrial 8% Packaging 5% Transportation 20% Wire & Cable 12% At a Glance Global Specialty Engineered Materials 2014 Revenues: $0.6 Billion Solutions 2014 Revenue by Industry Segment Expanding Profits 1.1% 1.3% 3.4% 5.1% 9.6% 8.0% 8.6% 9.3% 16.3% 20%+ 2006 2007 2008 2009 2010 2011 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales Platinum Vision 12.1% United States 44% Europe 33% Canada 2% Asia 19% Latin America 2% PolyOne Corporation Page 22 Appliances 2% Building & Construction 8% Consumer 5% Healthcare 6% Industrial 23% Packaging 27% Transportation 30% United States 96% Canada 4% At a Glance Designed Structures and Solutions Solutions 2014 Revenues: $0.6 Billion Expanding Profits 2014 Revenue by Industry Segment 1.4% 5.6% 7.3% 2.7% 12-14% 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales Platinum Vision PolyOne Corporation Page 23 Appliances 8% Building & Construction 33% Consumer 5% Electrical & Electronics 3% Healthcare 1% Industrial 11% Packaging 5% Transportation 18% Wire & Cable 16% 5.5% 6.9% 3.8% 3.6% 5.5% 4.3% 6.3% 7.2% 6.5% 2006 2007 2008 2009 2010 2011 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales At a Glance Performance Products and Solutions Solutions Expanding Profits 2014 Revenues: $0.8 Billion 10-12% Platinum Vision 2014 Revenue by Industry Segment 7.7% United States 80% Canada 14% Asia 2% Latin America 4% PolyOne Corporation Page 24 Appliances 6% Building & Construction 5% Consumer 13% Electrical & Electronics 6% Healthcare 23% Industrial 15% Packaging 4% Transportation 25% Wire & Cable 3% 2.6% 3.0% 3.5% 4.0% 4.6% 5.6% 6.4% 5.9% 5.9% 6.5-7.5% 2006 2007 2008 2009 2010 2011 2012 2013 2014 Q1 2015 2020 Operating Income % of Sales 15% 50% 2006 Q1 2015 At a Glance Distribution Key Suppliers 2014 Revenues: $1.1 Billion ROIC Expanding Profits 6.1% Platinum Vision http://www.avient.com/Pages/VariationRoot.aspx PolyOne Corporation Page 25 2 lbs Plastic = 3 lbs aluminum or 8 lbs steel or 27 lbs glass 33% less material by weight than aluminum 75% less material by weight than steel 93% less material by weight than glass Requires 91% less energy to recycle a pound of plastic versus a pound of paper Source: SPI: Sustainability and the Plastics Industry Plastics: Key to Future Sustainable Development PolyOne Corporation Page 26 Commitment to Operational Excellence 81% 93% 2006 2014 16.2% 9.9% 2006 2014 On-Time Delivery Working Capital % of Sales 5% 43% 2006 2014 Percent of Associates Trained in LSS  Four consecutive years – CFO Magazine Best Working Capital Management in the chemical industry World’s Best Business Process Excellence Program in 2012*  103 trained Black Belts  247 trained Green Belts  127 trained Kaizen Leaders World’s Best Start-up Program for Lean Six Sigma Deployment in 2009* *Both awards received from International Quality and Productivity Center PolyOne Corporation Page 27 Application Examples PolyOne Corporation Page 28  $1.5 billion attractive, growing market  Additives improve performance and reduce cost through light-weighting, reduced waste, faster cycle times, and extended shelf life of finished product  Aligned with megatrend of protecting the environment:  Sustainability benefits include lower package weight and improved recyclability of package at end of use Market Opportunity Leading Global Supplier of Additives In Growing PET Market Shelf-life extension Greater product consistency Recyclability and reduced carbon footprint Color and Special Effects Weight reduction Enhanced product aesthetics High heat resistance PET Bottling Technology 0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 2009 2014 2019 Asia Pacific North America Latin America Western Europe Eastern Europe Middle East and Africa Global PET Packaging Growth 2009-2019 Source: Euromonitor retail off-trade consumption (PET bottles & jars, home care, personal care, food & non-alcoholic beverages) B ill io n un its 5% CAGR PolyOne Corporation Page 29 • Includes formulation and consultative services to assist manufacturers and brand owners in positively identifying their finished goods • Protects brand equity & consumer welfare • Reduces exposure to unwarranted recall expenses • Secures supply chain integrity – support for safe expansion into new geographies Authentication Technology PolyOne Corporation Page 30 • Color harmonization across 15 unique color-and-polymer combinations • Eliminated need for multiple pre- colored materials • Reduced Land Rover’s working capital 2015 Range Rover Evoque Interior PolyOne Corporation Page 31 • Reduced health and environmental impact • System cost reduction • Radiation-shielding performance • Parts consolidation • Design freedom CT Scanner PolyOne Corporation Page 32 Metal Replacement Solutions • Replaces metal in LED lighting • Extends LED durability and life span eliminating hot spots • Greater design flexibility with fewer parts • Weight reduction • Simplifies manufacturing and lowers total production cost PolyOne Corporation Page 33 Next Generation Solar Charger • Ginkgo Solar Tree charger utilizing our unique reSound™ material • reSound™ is a durable material consisting of 50% bio-derived plastic and 50% traditional petroleum-based plastic • Use of reSound™ reduced the carbon footprint for this product by 35% • reSound™ Is classified as a PolyOne Sustainable SolutionSM PolyOne Sustainable SolutionSM PolyOne Corporation Page 34 High-Barrier Packaging Containers • Capability to extrude up to 13 layers • Strong oxygen and moisture vapor transmission protection • Can be made symmetrical or asymmetrical to meet customized needs of broad variety of applications • Barrier protection and superior organoleptic properties PolyOne Corporation Page 35 Aerospace Applications • Leading provider of specialty materials for the aerospace industry • Typical applications  Mil-spec aircraft windows, canopies, windscreens, instrument panels, wingtip lenses  Interior – gallery furnishings, tray tables, arm rests, trim strips, joint/edge coverings • Benefits:  High impact strength  Resistant to UV rays  Flame and smoke compliance  Easy to clean with aggressive cleaners; anti-microbial grades available  Range of sizes, thicknesses, colors, etc. 1 Schedule I Reconciliation of Non-GAAP Financial Measures (Unaudited) (Dollars in millions, except per share data) Below is a reconciliation of non-GAAP financial measures to the most directly comparable measures calculated and presented in accordance with U.S.

 Strong performance demonstrates that our strategy and execution are working  Megatrends and emerging opportunities align with our strengths  Innovation and services provide differentiation, incremental pricing power, and competitive advantage  Strong and proven management team driving growth and performance  Addressable market exceeds $40 billion PolyOne Corporation Page 17 Appendix PolyOne Corporation Page 18 +25% $262 $320 $200 $275 $350 2013 2014 Adjusted Operating Income (in millions) +22% 2014 Financial Highlights  All of our segments delivered both operating income and margin expansion during the year  Our specialty businesses achieved record levels of profits and profitability this year  Achieved 21st consecutive quarter, or over five years, of strong, double-digit adjusted EPS growth +37% $1.31 $1.80 $1.00 $1.50 $2.00 2013 2014 Adjusted EPS $195 $242 $150 $200 $250 2013 2014 Specialty Operating Income (in millions) PolyOne Corporation Page 19 Appliances 2% Building & Construction 12% Consumer 7% Electrical & Electronics 1% Healthcare 6% Industrial 14% Packaging 31% Textiles 7% Transportation 8% Wire & Cable 12% 1.7% 4.6% 5.1% 5.5% 7.2% 8.1% 9.7% 12.2% 12-16% 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 Operating Income % of Sales At a Glance Global Color, Additives and Inks 2014 Revenues: $0.9 Billion Solutions Expanding Profits 2014 Revenue by Industry Segment 14.7% Target United States 44% Europe 36% Canada 2% Asia 12% Latin America 6% PolyOne Corporation Page 20 Appliances 4% Building & Construction 3% Consumer 18% Electrical & Electronics 16% Healthcare 12% Industrial 8% Packaging 5% Transportation 20% Wire & Cable 12% At a Glance Global Specialty Engineered Materials 2014 Revenues: $0.6 Billion Solutions 2014 Revenue by Industry Segment Expanding Profits 1.1% 1.3% 3.4% 5.1% 9.6% 8.0% 8.6% 9.3% 12-16% 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 Operating Income % of Sales Target 12.1% United States 44% Europe 33% Canada 2% Asia 19% Latin America 2% PolyOne Corporation Page 21 Appliances 2% Building & Construction 8% Consumer 5% Healthcare 6% Industrial 23% Packaging 27% Transportation 30% United States 96% Canada 4% At a Glance Designed Structures and Solutions Solutions 2014 Revenues: $0.6 Billion Expanding Profits 2014 Revenue by Industry Segment 1.4% 5.6% 7.3% 8-10% 2012 2013 2014 2015 Operating Income % of Sales Target PolyOne Corporation Page 22 Appliances 8% Building & Construction 33% Consumer 5% Electrical & Electronics 3% Healthcare 1% Industrial 11% Packaging 5% Transportation 18% Wire & Cable 16% 5.5% 6.9% 3.8% 3.6% 5.5% 4.3% 6.3% 7.2% 2006 2007 2008 2009 2010 2011 2012 2013 2014 Operating Income % of Sales At a Glance Performance Products and Solutions Solutions Expanding Profits 2014 Revenues: $0.8 Billion 9-12% Target 2014 Revenue by Industry Segment 2015 7.7% United States 80% Canada 14% Asia 2% Latin America 4% PolyOne Corporation Page 23 Appliances 6% Building & Construction 5% Consumer 13% Electrical & Electronics 6% Healthcare 23% Industrial 15% Packaging 4% Transportation 25% Wire & Cable 3% 2.6% 3.0% 3.5% 4.0% 4.6% 5.6% 6.4% 5.9% 6 - 7.5% 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 Operating Income % of Sales 15% 52% 2006 2014 At a Glance Distribution *ROIC is defined as TTM adjusted OI divided by the sum of average debt and equity over a 5 quarter period Key Suppliers 2014 Revenues: $1.1 Billion ROIC* Expanding Profits 6.1% Target http://www.avient.com/Pages/VariationRoot.aspx PolyOne Corporation Page 24 2 lbs Plastic = 3 lbs aluminum or 8 lbs steel or 27 lbs glass 33% less material by weight than aluminum 75% less material by weight than steel 93% less material by weight than glass Requires 91% less energy to recycle a pound of plastic versus a pound of paper Source: SPI: Sustainability and the Plastics Industry Plastics: Key to Future Sustainable Development PolyOne Corporation Page 25 Commitment to Operational Excellence 81% 93% 2006 2014 16.2% 9.9% 2006 2014 On-Time Delivery Working Capital % of Sales 5% 43% 2006 2014 Percent of Associates Trained in LSS  Four consecutive years – CFO Magazine Best Working Capital Management in the chemical industry World’s Best Business Process Excellence Program in 2012*  103 trained Black Belts  247 trained Green Belts  127 trained Kaizen Leaders World’s Best Start-up Program for Lean Six Sigma Deployment in 2009* *Both awards received from International Quality and Productivity Center PolyOne Corporation Page 26 Prototype Frame Opportunity Scale-up & Test Market Build Business Case Commercial Launch Phase 1 Phase 2 Phase 3 Phase 4 Phase 5 4 11 5 10 6 9 3 4 2 15 9 1 10 4 Breakthrough Platform Derivative A Rich Pipeline of Opportunity Number of Projects 25 14 19 17 18 93 Addressable Market ($ millions) TBD TBD $800 $450 $450 $1,700 PolyOne Corporation Page 27 Application Examples PolyOne Corporation Page 28  $1.5 billion attractive, growing market  Additives improve performance and reduce cost through light-weighting, reduced waste, faster cycle times, and extended shelf life of finished product  Aligned with megatrend of protecting the environment:  Sustainability benefits include lower package weight and improved recyclability of package at end of use Market Opportunity Leading Global Supplier of Additives In Fast Growing PET Market Shelf-life extension Greater product consistency Recyclability and reduced carbon footprint Color and Special Effects Weight reduction Enhanced product aesthetics High heat resistance 4% 4% 8% 9% 9% 10% 11% 14% Western Europe North America South America MEA Easter Europe Asia Pacific China India PET 2008-13P CAGR PET Bottling Technology PolyOne Corporation Page 29 • Includes formulation and consultative services to assist manufacturers and brand owners in positively identifying their finished goods • Protects brand equity & consumer welfare • Reduces exposure to unwarranted recall expenses • Secures supply chain integrity – support for safe expansion into new geographies Authentication Technology PolyOne Corporation Page 30 • Color harmonization across 15 unique color-and-polymer combinations • Eliminated need for multiple pre- colored materials • Reduced Land Rover’s working capital Range Rover Evoque Interior PolyOne Corporation Page 31 • Reduced health and environmental impact • System cost reduction • Radiation-shielding performance • Parts consolidation • Design freedom CT Scanner PolyOne Corporation Page 32 Metal Replacement Solutions • Replaces metal in LED lighting • Extends LED durability and life span eliminating hot spots • Greater design flexibility with fewer parts • Weight reduction • Simplifies manufacturing and lowers total production cost PolyOne Corporation Page 33 Next Generation Solar Charger • Ginkgo Solar Tree charger utilizing our unique reSound™ material • reSound™ is a durable material consisting of 50% bio-derived plastic and 50% traditional petroleum-based plastic • Use of reSound™ reduced the carbon footprint for this product by 35% • reSound™ Is classified as a PolyOne Sustainable SolutionSM PolyOne Sustainable SolutionSM PolyOne Corporation Page 34 High-Barrier Packaging Containers • Capability to extrude up to 13 layers • Strong oxygen and moisture vapor transmission protection • Can be made symmetrical or asymmetrical to meet customized needs of broad variety of applications • Barrier protection and superior organoleptic properties PolyOne Corporation Page 35 Aerospace Applications • Leading provider of specialty materials for the aerospace industry • Typical applications  Mil-spec aircraft windows, canopies, windscreens, instrument panels, wingtip lenses  Interior – gallery furnishings, tray tables, arm rests, trim strips, joint/edge coverings • Benefits:  High impact strength  Resistant to UV rays  Flame and smoke compliance  Easy to clean with aggressive cleaners; anti-microbial grades available  Range of sizes, thicknesses, colors, etc. 1 Schedule I Reconciliation of Non-GAAP Financial Measures (Unaudited) (Dollars in millions, except per share data) Below is a reconciliation of non-GAAP financial measures to the most directly comparable measures calculated and presented in accordance with U.S.

Cost of response to risk 3,400,000 Description of response and explanation of cost calculation We are proud to have reached our original GHG emissions reduction target of reducing our emissions by 35% in 2021 by reducing our Scope 1 & 2 GHG emissions by 40%. We expect to invest in energy- and emissions-reducing activities at a similar or greater pace moving forward. Also in 2021, Avient completed 207 energy saving activities that cumulatively reduce yearly emissions by 5,500 MT CO2e, hence reducing the company exposure to commodity fluctuations and regulatory changes.

MEDICAL DEVICE DISINFECTION—HOW TO PREVENT CRACKING AND CRAZING Understanding polymer performance is key to minimizing disinfectant-related failures DISINFECTANT-RELATED DAMAGE ON POLYMER HOUSINGS Strong chemicals used to reduce hospital- acquired infections can damage equipment and result in material failures, such as: • Stress cracking • Crazing • Discoloration CHEMICAL RESISTANCE REQUIREMENTS VARY BY ENVIRONMENT • Patient/exam rooms • Operating and radiology rooms • Reception areas • Home (patient equipment & devices) Healthcare devices must perform flawlessly in a myriad of challenging environments and engineers must be certain their devices can withstand increasingly potent disinfectants, which have begun to outstrip the performance of traditional polymers. TECHNICAL BULLETIN SOLUTIONS DESIGNED TO ADDRESS EVOLVING NEEDS Determining the appropriate polymer for the job can prevent product failures, thereby reducing service calls, product returns and warranty claims for manufacturers.